Like the catalog number, the ISRC and the EAN code, the matrix number is an additional information which can help to identify a record. It consists of engraved (and/or printed) characters located around the label of a vinyl (or the inner circle of a CD). These characters are used by the factories in the stages of records pressing.
It is important to notice that:
- several records manufactured in the same series usually have exactly the same matrix numbers, this is not a unique identifier for each individual item
- records containing different sound masters might have same matrix number, so this might not be a unique and infallible way to distinguish different versions
- reversely, records having exactly the same content can have different matrix numbers
The SID Code is an anti-piracy standard defined by the IFPI and Philips in order to track the source of optical discs mastering and replication. The use of SID Codes started in 1994 and grew until nowadays it has become almost systematic.
Since not all plants have both mastering and replication facilities, two identification codes have been implemented:
- the Mastering SID Code that identifies the plant that manufactured the master
- the Mould SID Code that identifies the plant where the disc was replicated
Mastering SID Code
Sometimes also refered to as LBR Code (Laser Beam Recorder Code), it indicates the plant and LBR that manufactured the master or stamper used for the disc production.
It consists of the letters “IFPI” followed by a four or five alphanumeric digit code commencing with the letter “L”.
Example: IFPI L901
The Mastering SID Code must:
- Be positioned between 18.0 mm from the centre of the disc and the start of the “lead-in” (which is at a radius of 22.9 mm from the centre).
- Be a minimum of 0.5 mm high.
- Be legible without magnification.
- Be located in the metallised region of the disc.
- Read from left to right when viewed from the read-out, or play side of the disc. However many records seem not to follow this recommendation.
- Be installed in either the firmware of the LBR (i.e. the software that forms an intrinsic part of the machinery and is not readily accessible by the operator of the facility) or embedded in the system controller (i.e. the signal processing system that controls the operation of the LBR) in such a way that the operator of the system is not able to alter or remove/disable the code.
It is recommended that the space allocated exclusively for the code (determined by the user and LBR supplier) shall consist of an arc of 30º for the Mastering SID Code. It is mandatory that it is clearly separate from other features.
Mould SID Code
The mould SID Code indicates the plant where the disc was replicated and a serial number which can be set freely by the plant.
It consists of the letters “IFPI” followed by a four or five alphanumeric digit code. The first two digits (in the case of a four digit SID Code) or the first three digits (in the case of a five digit SID Code) are assigned to the operator of the manufacturing or mastering plant by Philips Intellectual Property & Standards. The last two digits of this code are allocated by the plant to give each mould on the site, including spare moulds, a unique code.
Example: IFPI 2U3Q
- The implementation guide implicitely recommends not to use “I”, “O”, “S” and “Q”. However many records seem not to follow this recommendation.
- The Mould SID Code must be positioned within a zone that has a maximum radius of 22.5 mm.
- If Burst Cutting Area - Code is used, then the position of the Mould SID Code will be adjusted to compensate.
- The Mould SID Code must not be imprinted in the clamping area.
- The Mould SID Code must not be placed in an area that obscures the Mastering SID Code or any other user defined characters.
- The Mould SID Code must be imprinted on all substrates whether containing valid programme content or not, including blank discs, and even if not metallised. Overprinting of the Mould Code for decorative purposes is permissible.
Code 39 (barcode)
This barcode is used to encode alphanumeric characters (A through Z and 0 and 9) and a few other characters such as the dollar or minus signs.
The DVD SID Code follow the same rules as the CD plus addionnal requirements:
- The Mastering SID Code must be placed within the zone that has a maximum radius of 22.5 mm.
- If Burst Cutting Area - Code is used, then the position of the Mastering Code should be adjusted to compensate.
- No minimum radius is specified, but due regard should be paid to the following points:
- The Mastering SID Code must be located in a metallised region of the disc.
- The Mastering SID Code must not be obscured by the stack ring.
- It is recommended that the space allocated exclusively for the code (determined by the user and LBR supplier) shall consist of an arc of 30º for the current code. It is mandatory that it is clearly separate from other features.
- A further arc of 30º shall be reserved for future use.
Single layer, single side disc
If the dummy side of the disc is made from a scrap program disc, it shall bear the SID Code, even if not metallised.
Dual layer, single side disc
The Mastering SID Code must be recorded for both layers (Layer 1 and Layer 0 in DVD format discs). At least one of the Mastering SID Codes (for either Layer 1 or Layer 0) must be clearly visible.
Single layer, double side disc
The Mastering SID Codes must be recorded on both sides of the disc. It is desirable that both Mastering SID Codes are clearly visible, but it is acceptable if the code is obscured due to restrictions of the printed area.